Cartridges & Styluses Blue 28 Items

DJ E Replacement stylus
Basic model for scratch and back-cueing. Outstanding rigidity by extra-strengthened cantilever

Features Special Elliptical stylus and a special developed and extremely balanced cantilever.

Not only does the cartridge have a most sufficient tracking ability, it is also nearly unbreakable and provides the DJs with the most needed stringency. Furthermore, it equals very low record wear, an advantage for busy DJ.

The DJ series has been known to many as the "jack of all trades," with improved tracking, alongside of accurate sound reproduction. Featuring a low wear stylus design, the DJ provides excellent groove handling, even with less weight applied.

DJ E Stylus Technical data
Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 2 dB
Channel separation at 1kHz - 23 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-22.000 Hz
Frequency response - 20-20.000 Hz +/-2 dB
Tracking ability at 315 Hz at recommmende tracking force - 80 μm
Compliance, dynamic lateral - 9 μm/m N
Stylus type - Special Elliptical
Stylus tip radius - r/R 13/25 μm

Tracking force range - 2.0-4.0 g (20-40 mN)
Tracking force recommended - 3.0 g (30 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
Concorde cartridge weight - 18.5 g

Compatible with cartridges - DJ S

The AT-VM95C, the new Audio-Technica entry model Conical cartridge will replace the legendary AT90 Series models such as AT91, AT91R and CN5625AL

Also the AT-VM95C is a “budget” cartridge featuring a conical stylus, the compatibility in the range will allow to upgrade with any of the 4 other LP styli of the Series such as Elliptical, Elliptical Nude, Microlinear and Shibata.

Aluminium cantilever
4.0mV output voltage
Compatible body with all VM95 Series stylus assemblies
Replacement for AT91, AT91R and CN5625AL

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

AT-VM9E SERIES COMPATIBILITY WITH THE AT-XP SERIES DJ CARTRIDGES
The electromagnetic engine-body of XP-Series, is fully compatible with all replacement styli of VM95 Series and will deliver more output voltage than VM95 Series cartridge. So providing improved compatibility with phono inputs of Professional DJ Mixers.
VM95 Series electromagnetic engine-body is also compatible with the three replacement styli of the DJ cartridge AT-XP Series, nevertheless, the electromagnetic engine-body of XP-Series, will deliver more output voltage than VM95 Series cartridge in order to provide better compatibility with phono inputs of Professional DJ Mixers.
Note that typical tracking force when using XP Series styli is three grams as opposed to two grams for VM95 Series styli.
The suspension design and compliance of XP-Series styli have been optimized for intensive DJ’ing, including possible manual cueing and back-cueing.
The VM95 Series suspension design and compliances of VM95 Series have been designed for optimum audiophile reproduction.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely.

Model AT-VM95C
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 20,000 Hz
Kanaltrennung 18 dB (1 kHz)
Kanalbalance am Ausgang 2.5 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Conical
Nadelabmessungen 0.6 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 6.5 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 6.1g
Abmessungen 17.2 x 18.9 x 28.3 ( H x W x D mm)
Ersatznadel AT-VMN95C
Beiliegendes Zubehör Two 11 mm installation screws;
Two 8 mm installation screws;
Two washers

The new stylus features
Replacement stylus offers a tactile feedback when seating, indicating a snug and secure fit, while a cut-out area in the front allows for far more accurate needle drops.

• Larger, wider and more robust stylus body
• Easier to grip and handle
• Better fix by metal spring
• Tactile feedback of correct mount
• Large stylus viewing cut‐out

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 1 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 100 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical R 18 μm

Tracking force range - 3 - 5 g
Tracking force recommended - 4 g
Recommended exclusively for Concorde MkII DJ

Attention: Matches the new Concorde MkII only!

Excellent groove handling
The Concorde DJ is considered the jack-of-all-trades, boasting accurate sound reproduction and excellent groove handling.

• The DJ is great for any style of music.
• It has a spherical stylus and an extremely balanced cantilever that provides outstanding rigidity.
• Not only does the cartridge have a most sufficient tracking ability, it also provides the DJs with the most needed stringency and very low record wear.

All in all: improved tracking, alongside of accurate sound reproduction and an excellent groove handling.

Output voltage at 1000Hz, 5cm/sec. - 6 mV
Channel balance at 1kHz - 1 dB
Channel separation at 1kHz - 22 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Tracking ability at 315 Hz at recommmended tracking force - 100 μm
Compliance, dynamic lateral - 14 μm/m N
Stylus type - Spherical R 18 μm
Tracking force range - 3 - 5 g
Tracking force recommended - 4 g

Cartridge weight - 18,5 g
Replacement stylus unit - DJ

The 2M Series of cartridges is designed for precise and accurate retrieval of the information in the record groove. Our philosophy is to play the record sound as accurate as possible, without coloring the sound

The name 2M was selected from several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.
The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.
We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue Series features:

an improved engine, which provides an increased output of 5.5mV
Nude Elliptical diamond and split pole pins with a copper wire

Technical data:
• Frequency range 20-25.000 Hz
• Frequency response 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force *) 80 µm
• Compliance, dynamic, lateral 20 µm/mN
• Stylus type Nude Elliptical
• Stylus tip radius r/R 8/18 µm
• Equivalent stylus tip mass 0,5 mg
• Tracking force range 1,6-2,0 g (16-20 mN)
• Tracking force, recommended 1,8 g (18 mN)
• Tracking angle 20°
• Stylus colour Blue

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Blue features:

• an improved engine, which provides an increased output of 5.5mV and an optimized sound reproduction and a high level of sonic accuracy

• Nude Elliptical diamond and split pole pins with a copper wire

• The cartridge body is manufactured from Hopelex, an environment-friendly material which ensures high rigidity while eliminating unwanted resonances

2M Blue adds more dynamics and resolution, sounds more open and reproduces more details than 2M Red

Output voltage at 1000 Hz, 5cm/sec. - 5,5 mV
Channel balance at 1 kHz - 1,5 dB
Channel separation at 1 kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at - 3dB - 20-25.000 Hz
Frequency response - 20-20.000 Hz + 2 / - 1 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 20 µm/mN
Stylus type - Nude Elliptical
Stylus tip radius - r/R 8/18 µm
Tracking force range - 1,6-2,0g (16-20 mN)
Tracking force, recommended - 1,8 g (18 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1,3 kOhm
Internal inductance - 700 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Blue
Cartridge weight - 7,2 g
Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

Replacement stylus Nagaoka JTS-80LB for the pickup JT-80LB.

The Nagaoka JT-80LB (Lapis Blue) cartridge with its shiny blue needle insert is the basic model of the series and features an aluminium needle carrier with a set diamond. With its open, powerful sound, it offers exceptional value for money. The cartridge unfolds its full potential after an approx. 80-hour play-in period.

TECHNICAL SPECIFICATIONS:
• Format: Moving magnet type (MM type)
• Output: 5.0 mV (5 cm / sec)
• Frequency characteristic: 20Hz-20,000Hz
• Channel separation: 23dB (1Khz)
• Channel balance: 1.5 dB or less
• Cantilever: Aluminum alloy
• Needle tip: 0.4x0.7mil Ellipse / Joined diamond
• Stylus pressure: 1.3g-1.8g
• Torridge own weight: 6.9g
• Replacement needle: JTS-80LB
• Cartridge type: without head shell

https://www.auditorium.de/attachment/STEREO_3-21_Nagaoka-Abtaster_englisch.pdf

OM Scratch White pre-mounted on SH-4 Blue headshell
The OM Scratch White on the SH-4 Black headshell is a practical and convenient solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm.

Features:
• Universal mount fitting a wide range of S-shaped tonearms
• Correct Baerwald alignment with the major part of tonearms with universal mount
• Spherical stylus minimizes scratching
• Increased tracking ability
• Reinforced rubber suspension

High output and maximum scratch performance guaranteed!

OM Scratch White technical data
Stylus Type Spherical
Tracking Force 4.0 g (40 mN)
Output Voltage 7 mV
Frequency Range 20-15.000 Hz

Output voltage at 1000Hz, 5cm/sec. - 7 mV
Channel balance at 1kHz - 1,5 dB
Channel separation at 1kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at -3dB - 20-20.000 Hz
Frequency response - 20-15.000 Hz 3dB/-2dB
Tracking ability at 315 Hz at recommmended tracking force - 80 μm
Compliance, dynamic lateral - 6 μm/m N
Stylus type - Spherical
Stylus tip radius - R 18 μm
Tracking force range - 3,0-5,0 g (30-50 mN)
Tracking force recommended - 4,0 g (40 mN)
Tracking angle - 20°

Internal impedance, DC resistance - 750 Ohm
Internal inductance - 450 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 200-600 pF
OM cartridge weight - 5 g
OM pre-mounted on SH-4 weight incl. screws - 14,5 g

Replacement stylus unit - Scratch White

ATN-XP3
Replacement Stylus for AT-XP3
Conical Bonded Stylus
Carbon fibre-reinforced ABS cantilever
Durable design for DJ application

•Excellent for scratching
•Very high tracking ability
•Very low vinyl wearout

The Concorde Blue cartridge system is particularly suitable for scratching, due to the special spherical stylus. With a very high tracking ability, the cartridge always stays in the record groove and does not jump, even during fast manoeuvres. In addition, the stylus has a positive effect on vinyl wear.

FEATURES
•Excellent for scratching
•Special spherical stylus
•Very high tracking ability
•High output voltage
•Very low vinyl wearout
•Easy tonearm installation through direct SME mounting
•Made by Ortofon

TECHNICAL DATA
•Frequency range: 20 Hz - 18 kHz
•Output voltage (5 cm/s): 6 mV
•Tracking force range: 2 - 5 g
•Recommended tracking force: 4 g
•Weight: 18.5 g

AT-VMN95C
VM95 SERIES CONICAL REPLACEMENT STYLUS
Aluminium cantilever
Conical stylus
Bonded Round Shank

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely.

AT-VM95C/H
VM95 SERIES CONICAL STEREO CARTRIDGE ON AT-HS6 HEADSHELL
AT-VM95C mounted on AT-HS6BK headshell
The total set weight is 15.5g
Assembled and tested in the Audio-Technica Factory in Fukui-Japa

VM95 SERIES - STYLI COMPATIBILITY
Every cartridge diamond stylus becomes worn after a period of play.

Around 500 hours for a conical stylus, 300 hours for an Elliptical stylus, 1000 hours for a Microlinear stylus, and 800 hours for a Shibata stylus.

Our VM95 Series dual moving magnet cartridges can be used almost forever by replacing the interchangeable stylus. It is no longer necessary to purchase a complete cartridge when your diamond is worn out, you can simply buy the matching replacement stylus, but also enjoy the experience of upgrading your cartridge with a different stylus.

The six models of VM95 Series cartridges all use the same electromagnetic engine-body, therefore each of the six replacement styli are perfectly compatible.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely.

PREASSEMBLED WITH AT-HS6BK HEADSHELL
The AT-VM95C cartridge is fitted onto the 9g aluminium die cast body headshell

Model AT-VM95C/H
Typ VM Stereo Dual Magnet
Befestigung 1/2” centres
Frequenzbereich 20 - 20,000 Hz
Kanaltrennung 18 dB (1 kHz)
Kanalbalance am Ausgang 2.5 dB (1 kHz)
Ausgangsleistung 4.0 mV (at 1 kHz, 5 cm/sec)
Vertikaler Abtastwinkel 23°
Vertikaler Auflagekraftbereich 1.8 - 2.2g (standard 2.0 g)
Nadelschliff Conical
Nadelabmessungen 0.6 mil
Schaftform der Nadel Bonded Round Shank
Nadelträger Aluminium Pipe
Spulenimpedanz 3.3 kΩ (1 kHz)
Spuleninduktivität 550 mH (1 kHz)
DC Widerstand 485 Ω
Statische Nadelnachgiebigkeit 17 x 10 – 6 cm / dyne
Dynamische Nadelnachgiebigkeit 6.5 x 10 – 6 cm / dyne (100 Hz)
Spulendraht T.P. Copper
Empfohlene Lastimpedanz 47,000 Ω
Empfohlene Lastkapazität 100-200 pF
Gewicht 15.5 g
Abmessungen 21.2 × 21.4 × 62.4 ( H x W x D mm)
Ersatznadel AT-VMN95C

VMN10CB
REPLACEMENT STYLUS FOR VM510CB & VM610MONO
Conical Bonded stylus
Bonded Round Shank construction
Blue

VMN20EB
REPLACEMENT STYLUS FOR VM520EB
Elliptical Bonded stylus
Bonded Round Shank construction
Blue

VM510CB
DUAL MOVING MAGNET STEREO CARTRIDGE WITH CONICAL STYLUS
Conical Bonded stylus
VM type dual magnet system
Para-toroidal coils improve generating efficiency
Aluminium cantilever
Centre shield plate between stereo channels
Durable low resonance polymer housing

Conical Bonded stylus for less critical tilt angle adjustment allowing more flexible use on various tonearms.
VM type dual magnet design ensures outstanding channel separation, extended frequency response and superb tracking
Lightweight tapered aluminium cantilever allows for faithful reading of the record groove
Centre shield plate enables the effective separation of left and right channels, suppressing electrical crosstalk to below 40dB
Durable low resonance polymer housing

Entry-level VM cartridge model equipped with a conical bonded stylus. The round stylus is less likely to be affected by placement and boasts stable tracing performance.

Aluminium cantilever
Para-toroidal coils improve generating efficiency
Centre shield plate between the left and right channels reduces crosstalk
Durable low resonance polymer housing

AUDIO-TECHNICA’S INTERNATIONALLY-PATENTED DUAL MAGNET DESIGN REPLICATES THE STRUCTURE OF THE CUTTER HEAD.
Instead of using a single, large magnet, the two magnets are arranged in the shape of a "V". The two magnets are positioned precisely to match the positions of the left and right channels in the stereo groove walls. Consequently, the VM design ensures outstanding channel separation, extended frequency response and superb tracking.

Para-toroidal generating system

Para-toroidal coils improve generating efficiency and offers superb linearity, since leakage of magnetic flux in this continuous and unitised magnetic circuit is low. Permeability of the cores is also optimised through the use of laminated cores.

Centre shield plate reduces crosstalk

A permalloy centre shield plate enables the effective separation of left and right channels, suppressing electrical crosstalk to below 40dB. This is similar to the actual crosstalk value found in the grooves of the record itself.

500 SERIES
Standard cartridge body fitted with the para-toroidal coils, centre shield plate, and 6N-OFC coil wire which is the same as 700 series.

CONICAL BONDED STYLUS
The benefit of conical styli, even if the cartridge is "lean", is the ball surface of the stylus touches the groove of vinyl records precisely. Due to its stability, it has been used widely at radio stations.

Type VM Type
Mounting 1/2” centres
Frequency Response 20 - 20,000Hz
Channel Separation 25dB (1kHz)
Output Channel Balance 1.5dB (1kHz)
Output Voltage 5.0mV (1kHz, 5cm/sec.)
Vertical Tracking Angle 23˚
Vertical Tracking Force Range 1.8 – 2.2g (2.0g standard)
Stylus Shape Conical Bonded
Stylus Size 0.6 mil
Stylus Construction Bonded Round Shank
Cantilever Aluminium Pipe
Coil Impedance 2,700Ω (1kHz)
Static Compliance 35 x 10-6 cm/dyne
Dynamic Compliance 8 x 10-6 cm/dyne (100Hz)
Recommended Load Impedance 47,000Ω
Recommended Load Capacitance 100 – 200pF
Weight 6.4g
Dimensions 17.3 (H) x 17.0 (W) x 28.2 (L) mm
Replacement Stylus VMN10CB
Accessories Included Cartridge installation screws 5mm ×2 and 10mm ×2, Washer ×2, Hexagon nut ×2

VM Cartridges: https://eu.audio-technica.com/resources/VM_Cartridges_EN.pdf

Manual: https://eu.audio-technica.com/resources/VM/VM510CB_UM_V2_11L_web_161011.pdf

VM520EB
DUAL MOVING MAGNET STEREO CARTRIDGE WITH ELLIPTICAL STYLUS
Elliptical Bonded profile diamond stylus
VM type dual magnet system
Para-toroidal coils improve generating efficiency
Aluminium cantilever
Centre shield plate between stereo channels
Durable low resonance polymer housing

Standard elliptical stylus model equipped with an elliptical bonded stylus. This reduces tracing distortion and allows for more accurate sound reproduction.

Aluminium cantilever
Para-toroidal coils improve generating efficiency
Centre shield plate between the left and right channels reduces crosstalk
Durable low resonance polymer housing

AUDIO-TECHNICA’S INTERNATIONALLY-PATENTED DUAL MAGNET DESIGN REPLICATES THE STRUCTURE OF THE CUTTER HEAD.
Instead of using a single, large magnet, the two magnets are arranged in the shape of a "V". The two magnets are positioned precisely to match the positions of the left and right channels in the stereo groove walls. Consequently, the VM design ensures outstanding channel separation, extended frequency response and superb tracking.

Para-toroidal generating system

Para-toroidal coils improve generating efficiency and offers superb linearity, since leakage of magnetic flux in this continuous and unitised magnetic circuit is low. Permeability of the cores is also optimised through the use of laminated cores.

Centre shield plate reduces crosstalk

A permalloy centre shield plate enables the effective separation of left and right channels, suppressing electrical crosstalk to below 40dB. This is similar to the actual crosstalk value found in the grooves of the record itself.

500 SERIES
Standard cartridge body fitted with the para-toroidal coils, centre shield plate, and 6N-OFC coil wire which is the same as 700 series.

ELLIPTICAL BONDED STYLUS
Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

Type VM Type
Mounting 1/2” centres
Frequency Response 20 - 23,000Hz
Channel Separation 27dB (1kHz)
Output Channel Balance 1.5dB (1kHz)
Output Voltage 4.0mV (1kHz, 5cm/sec.)
Vertical Tracking Angle 23˚
Vertical Tracking Force Range 1.8 – 2.2g (2.0g standard)
Stylus Shape Elliptical Bonded
Stylus Size 0.3 x 0.7 mil
Stylus Construction Bonded Round Shank
Cantilever Aluminium Pipe
Coil Impedance 2,700Ω (1kHz)
Static Compliance 35 x 10-6 cm/dyne
Dynamic Compliance 8 x 10-6 cm/dyne (100Hz)
Recommended Load Impedance 47,000Ω
Recommended Load Capacitance 100 – 200pF
Weight 6.4g
Dimensions 17.3 (H) x 17.0 (W) x 28.2 (L) mm
Replacement Stylus VMN20EB
Accessories Included Cartridge installation screws 5mm ×2 and 10mm ×2, Washer ×2, Hexagon nut ×2

VM Cartridges: https://eu.audio-technica.com/resources/VM_Cartridges_EN.pdf

Manual: https://eu.audio-technica.com/resources/VM/VM520EB_UM_V2_11L_web_161021.pdf

The 2M Series is developed in conjunction with the Danish Industrial designer Møller Jensen Design – the same designer who designed the award winning MC Jubilee and Kontrapunkt series. Inspired by the facets of a diamond, whose contours gracefully trace the grooves on a record’s surface, the 2M’s handsome elegance establishes a great combination of form and functionality.

The name 2M was selected from among several ideas. We wanted a modern name that would be easy to pronounce and remember, and therefore an alphanumerical name was chosen. 2M means MM, which is the abbreviation for moving magnet.

Of course the 2M isn’t just another pretty face. It has been engineered to the highest standards and is congruent with Ortofon’s unrelenting commitment to providing the most precise and accurate reproduction possible without coloration.

The 2M series of cartridges features Ortofon’s trademark split pole pins, an invention that enables moving magnet cartridges to have a flat frequency response, as with a moving coil cartridge. Split pole pins were invented by Ortofon, and were originally presented in the 500 series and Super OM series.

We have optimized the design for ease of mounting the cartridge, and the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

2M Blue features:

• an improved engine, which provides an increased output of 5.5mV and an optimized sound reproduction and a high level of sonic accuracy

• Nude Elliptical diamond and split pole pins with a copper wire

• The cartridge body is manufactured from Hopelex, an environment-friendly material which ensures high rigidity while eliminating unwanted resonances

2M Blue adds more dynamics and resolution, sounds more open and reproduces more details than 2M Red

Output voltage at 1000 Hz, 5cm/sec. - 5,5 mV
Channel balance at 1 kHz - 1,5 dB
Channel separation at 1 kHz - 25 dB
Channel separation at 15 kHz - 15 dB
Frequency range at - 3dB - 20-25.000 Hz
Frequency response - 20-20.000 Hz + 2 / - 1 dB
Tracking ability at 315Hz at recommended tracking force - 80 µm
Compliance, dynamic, lateral - 20 µm/mN
Stylus type - Nude Elliptical
Stylus tip radius - r/R 8/18 µm
Tracking force range - 1,6-2,0g (16-20 mN)
Tracking force, recommended - 1,8 g (18 mN)
Tracking angle - 20°
Internal impedance, DC resistance - 1,3 kOhm
Internal inductance - 700 mH
Recommended load resistance - 47 kOhm
Recommended load capacitance - 150-300 pF
Cartridge colour, body/stylus - Black/Blue
Cartridge weight - 7,2 g
Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Each of the 2M Series cartridges has its own individual sonic expression, and all five models together represent the ensemble of five classic variations:

• 2M Mono SE, 2M Mono and 2M 78 are a true mono cartridges for playing mono vinyl records
• 2M Red is an all-purpose cartridge that delivers open, dynamic sound with a slight touch of warmth
• 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details
• 2M Bronze adds even more details and resolution but in a very evenhanded way that pays respect to all elements
• 2M Black is the best of everything, true to the groove with resolution and accurate insight into each recording

Introducing Concorde Music
Developed by music lovers, for music lovers, the Concorde Music cartridges blend premium performance with an iconic design.
Concorde Music, not just a cartridge, but a dedication to the profound impact music has on our lives, turning every listening session
into a captivating journey.

Possibly the world’s most iconic cartridge design
Building upon a rich legacy which began when we launched the original Concorde, the Concorde Music holds a storied history as
one of the most famous cartridges in the world of audio. Originally developed as a solution to the challenge of easy mounting on a
tonearm without screws or wires, the Concorde's unique design earned the Danish Industrial Design Award and became an icon in
the audio industry.

Features:
• Diamond: Each Concorde Music stylus features a diamond polished to the highest standards of the industry. Ranging from
a bonded Elliptical diamond on Concorde Music Red, to a Nude Shibata diamond on Concorde Music Black LVB 250.
• Cantilever: All Concorde Music models have a premium or high-end cantilever. The cantilever material is either aluminium
or boron for the best possible transmission of the vinyl record groove modulations picked up by the diamonds.
• Suspension: Exclusive Ortofon rubber compounds are used for the stylus suspensions, all carefully produced at the in_x0002_house own rubber production, and developed by the research and engineering team at Ortofon for brilliant performance.
• Coil system: Silver-pated oxygen free copper is chosen for the quad-coil system together with four Ortofon split pole pins
delivering a 6 mV output of dynamic, lifelike sound with an exceptional clarity and fidelity, capturing every detail.
• Upgradeability: All Concorde Music styli are compatible with all Concorde Music cartridges. An upgrade path is possible
through the entire series of Concorde Music cartridges, enabling upgrades from Concorde Music Red to Black LVB 250.
• Tool-free installation: Installing a Concorde Music cartridge on a turntable is easy and straightforward, no tools required
making it hassle free and convenient for all users.

It is all about the music
Concorde Music stands as an icon of design and musical dedication, inviting everyone to elevate their journey with the level of
accuracy in sound which has become characteristic for every Ortofon cartridge. Tailored for music lovers, incorporating a
straightforward installation, premium sound, and a timeless design. Concorde Music stands for a commitment to musicality.

Unique in-house rubber production a crucially important and vital part of a phono cartridge overall performance is the stylus
rubber suspension. Ortofon develops exclusive rubber compounds and produce the rubber suspensions and dampers in-house.

Ortofon quad-coil generating system with split pole pins in Concorde Music results in an exceptional channel balance and channel
separation, delivering a precise and dynamic sound image.

Ortofon, we love music!

2MR: the newest addition to the renowned 2M Series
Ortofon 2MR features a specially designed cartridge housing tailored for turntables and tonearms like Rega matching their requirement for low-form factor cartridges. With its narrow cartridge housing, it seamlessly integrates without a need for modifications or spacers under the tonearm, enabling quick and easy mounting with just two screws. Ortofon 2MR cartridges features unique to Ortofon technologies like: High-performance quad coil motor system with split pole pins, Proprietary Ortofon premium and high-end rubber dampers plus full compatibility with the Ortofon 2M series styli.

Authentic sound reproduction
2MR continues the 2M Series' commitment to authentic sound reproduction.
A high-performance motor system featuring quad coils and split pole pins minimizes eddy current losses, enhancing channel balance and accuracy.
This innovation results in a clean, detailed, and true-to-life sound, faithfully capturing the nuances of your cherished vinyl collection.

More than just a cartridge
2MR cartridge are for those who value an authentic immersive listening experience when listening to their music. 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.
The 2MR maintains the hallmark of interchangeability, allowing you to explore your records in greater depth and detail. The seamless transition between stylus profiles lets you tailor your listening experience, ensuring every note is heard with unparalleled accuracy and emotion. The 2MR series empowers you to explore your records like never before, allowing you to savor every moment of your favorite music.
The 2MR lets you rediscover your vinyl collection with enhanced clarity and precision.

2MR cartridge key features:
• Slimline cartridge body effectively eliminates the need for tonearm spacers, shims or modifications on turntables needing a low form factor cartridge.
• High-performance motor system incorporating unique to Ortofon quad coils with split pole pins, delivering a clean detailed and true-to-life sound.
• 100% compatibility with the 2M styli Ortofon 2MR use the well-known 2M styli.
• Standard half inch mounting quick and easy mounting on the tonearms with just two screws.
• Full range setup 2MR ranges from Mono to Premium: 2MR Red to High-end: 2MR Black LVB 250

Next level authenticity with the 2M Blue
The goal for any cartridge should be to reproduce the sound as close to the artists vision as possible, and the 2M blue takes you further on this journey of authenticity. With the 2M Blue, you get serious about listening to vinyl.

Features:
The 2M Blue features a Nude Elliptical diamond and split pole pins with a copper wire.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details compared to the 2M Red model.

Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 25 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Blue
• 2MR cartridge weight - 6 g
• 2M and 2M Verso cartridges weight - 7.2 g
• 2M Premounted cartridge weight - 16.7 g

Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Stylus lifetime:
with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze and 2M Black
- 2M Mono and 2M 78

Replacement stylus Nagaoka G JN-03D for the pickup DJ-03HD.

DJ-03 HD - CARTRIDGE INCL. HEADSHELL

This is the Nagaoka DJ cartridge. With a high output voltage of 6 mV and a recommended tracking force of 3 - 5 g, it is one of the more stable of its kind.

TECHNICAL SPECIFICATIONS:
• Cartridge type: MM
• Configuration: Climax DS/DSM
• Output voltage: 6 mV (5 cm/sec.)
• Frequency Characteristics: 20Hz~20KHz
• Channel separation: 20 dB (1 kHz)
• Channel balance: 2 dB or less
• Load resistance: 47 kΩ
• Load: 100pF
• Cantilever: aluminum alloy
• Needle Tip: 0.6 mil tapered bonded diamond
• Recommended tracking force: 3~5g
• Pickup weight: 5.1g
• Weight with headshell: 15.1g

Stylus for Goldring E4 MM Cartridge

Just needle, not the complete cartridge included!

Next level authenticity with the 2M Blue
The goal for any cartridge should be to reproduce the sound as close to the artists vision as possible, and the 2M blue takes you further on this journey of authenticity. With the 2M Blue, you get serious about listening to vinyl.

Features:
The 2M Blue features a Nude Elliptical diamond and split pole pins with a copper wire.

Designed for easy mounting of the cartridge, and for the weight and size to fit the most common turntables on the market today. The 2M Series provides excellent compatibility when used in an assortment of playback systems and with a wide variety of phono preamps.

The 2M Blue adds more dynamics and resolution, sounds more open and reproduces more details compared to the 2M Red model.

2M Blue Technical data:
• Output voltage at 1000 Hz, 5cm/sec. - 5.5 mV
• Channel balance at 1 kHz - 1.5 dB
• Channel separation at 1 kHz - 25 dB
• Channel separation at 15 kHz - 15 dB
• Frequency response - 20-20.000 Hz + 2 / - 1 dB
• Tracking ability at 315Hz at recommended tracking force - 80 µm
• Compliance, dynamic, lateral - 20 µm/mN
• Stylus type - Nude Elliptical
• Stylus tip radius - r/R 8/18 µm
• Tracking force range - 1.6-2.0 g (16-20 mN)
• Tracking force, recommended - 1.8 g (18 mN)
• Tracking angle - 20°
• Internal impedance, DC resistance - 1.3 kOhm
• Internal inductance - 700 mH
• Recommended load resistance - 47 kOhm
• Recommended load capacitance - 150-300 pF
• Cartridge colour, body/stylus - Black/Blue
• Cartridge weight - 7.2 g
• Premounted cartridge weight - 16.7 g
• Replacement stylus unit - 2M Blue (interchangeable with 2M Red and 2M Silver)

Stylus lifetime: with proper care we find that up to 1000 hours is possible without degradation of performance.

2M Series styli interchangeability:
The 2M Series' engines, coils and magnets configurations are not identical: Red and Blue are identical, so are the Bronze and Black and so are the true mono variants 2M Mono and 2M 78. Likewise, 2M series styli are interchangeable within the below combinations:
- 2M Red, 2M Blue and 2M Silver
- 2M Bronze, 2M Black and 2M Black LVB 250
- 2M Mono and 2M 78

Compatibility with Rega brand TT/TA:
REGA brand cartridges’ height from stylus tip to the top cartridge mounting surface is lower than standard. Therefore you would need spacers to ensure the correct set-up of the Ortofon cartridge.
Adjusting the height of your Rega tonearm is easy with Acoustic Signature's Spacer Set. It allows you to adjust the height from 0.5 mm to 3.5 mm in precise steps of 0.5 mm - without removing the tone arm. Simply loosen the screws, insert the AS-spacer, then lock the screws back down, and you're tonearm is ready to play.
3.2 - 4 mm spacers should be enough for 2M cartridge.

With the 2M Premounted, it’s never been easier to experience
The 2M Premounted is a practical and elegant solution for our customers who wish direct and easy mounting and replacement on their S-shaped tonearm. The quality of the SH-4 headshell is sturdy and rigid, yet the design emphasizes a slim and delicate form factor. The strong, lightweight headshell has an ergonomic design with a long finger lift that is easy to pick up.

Features:
- Premounted on our popular SH-4 Black headshell.
- Easy and direct mount on S-shaped tonearms with universal mount.
- Correct Baerwald alignment with tonearms with universal mount.